This is equivalent to Moving a file from the source to the destination. Move Mode: Delete Source after Copy (1-way Jobs, un-checked by default)Īfter file is copied from source folder to destination folder, GoodSync will delete it. If not checked then GoodSync will assign an empty ACL to copied files. If checked then GoodSync will copy file/folder Access Control List (ACL). If not checked then GoodSync assigns the current owner to copied files.Ĭopy ACL (NFTS-to-NFTS only, un-checked by default) If checked then GoodSync will copy the file/folder owner. If not checked then GoodSync will assign the normal Attribute to copied files.Ĭopy Owner (Mac-to-Mac or NFTS-to-NFTS only, un-checked by default) If checked then GoodSync will copy file/folder Attributes (Hidden, System, ReadOnly, and Archive). If not checked then GoodSync will copy only the modification time of the file/folder.Ĭopy Attributes (Windows-to-Windows only, checked by default) If checked then GoodSync will copy both the creation and modification time of the file/folder. If checked, GoodSync automatically deletes the changes tree after a Job run.This is an overview of the "Advanced" section in Job Options.Ĭopy File Creation Time (checked by default) If checked, auto jobs wait for lock files to clear instead of producing an error.Īuto Clear the tree after Analyze/Sync has finished (unchecked by default) Wait for Locks to clear (checked by default) This will ensure that the runner may impersonate the user account and have appropriate access to the data.ĭo Not Sync if changed files more than (checked, 50% by default)Īutomated sync (2-way mode only) is not performed if more than the specified (in percent) fraction of files in the job has changed.Īn unusually high number of changed files typically indicates an event that requires user attention (e.g. When checked, GoodSync will initiate the Runner Service Setup (which can also be run through Tools > Runner Service Setup) and request the Windows account password for the currently logged-in user. This will allow scheduled jobs to execute even if the user is logged off or the application is closed. If checked, jobs will run through the GoodSync Runner Service. This option applies to all auto modes except for "On Start" and "On Logoff". Ensure that Control Panel > Power Options > Change Plan Settings > Change Advanced Power Settings > Sleep > Allow Wake Timers is enabled. ![]() If your computer goes to Sleep/Standby, GoodSync can wake it up for the "On Schedule" job. NOTE: If a field is left empty, it will run for every unit value of its range. NOTE: Does not work in Unattended mode as the GoodSync Runner service always runs.Īnalyze and sync this job on a specified schedule. Normally Windows sees that GoodSync is performing file operations and allows completion, but results may vary. Note that Windows may try to close GoodSync on Logoff. Periodically (On Timer) (default period: 2 hours 0 minutes)Īnalyze and sync this job periodically, every HH hours and MM minutes.Īnalyze and sync this job just before Logoff from Windows. NOTE: This feature does not work in Unattended mode as the GoodSync Runner service always runs. The Delay value specifies the number of seconds to wait since the GoodSync application started. Should not be used together with the " On File Change" mode as the former overrides it.Īnalyze and sync this job when GoodSync starts up. – Network connect or disconnect: FTP, SFTP, and DAV folders may connect or disconnect. – Insertion or ejection of a portable volume: detachable folders may connect or disconnect. The following events speed up the detection of a connected/disconnected status: NOTE: If changes occur during analysis/sync, they are still detected and sent to the next analysis interval.Īnalyze and sync this job when a specified location is made available.īy design, GoodSync checks every 3 minutes for the status of the left and right folders to determine availability. – Any of the above file systems remotely accessed via the GSTP protocol using GoodSync Connect. ![]() – Windows shares (except for some faulty NAS shares that do not report changes). ![]() – Windows File System and local disks (except root folder). "On File Change" supports the following file systems: ![]() The Delay value specifies the number of seconds to wait since the last detected change before starting the analysis and sync. Monitors source and/or destination for changes and replicates them in real time.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |